Get Your Quote

Item Tag: LCR Meter

LCR Meter LCR Component Tester LCR Tester 2.4″ TFT Color Screen Chinese English

Description LCR Meter LCR Component Tester LCR Tester 2.4″ TFT Color Screen Chinese English Description: The NJ series impedance tester adopts a high-performance processor and ultra-low power consumption design. It is a portable product mainly used to measure parameter performance of three basic components (resistance R, capacitance C, and inductance L). The product has a built-in large-capacity lithium-ion battery. It is small in size, light in weight, and easy to carry. It is more convenient to use for outdoor and high-altitude special operations. Display screen interface and buttons are clear and simple, at a glance, Chinese and English can be set by yourselves, easy to use and simple to operate. It is designed with online test function. Main Features: 1. Test frequency range is wide. 2. Small size, light weight, easy to carry. Appearance size: 130*108*31 (mm); net weight: 315g. 3. Built-in battery, using 2000mAH polymer lithium battery, continuous working time exceeds 8 hours. 4. High resolution, and measurement result is in 6-digit. 5. With calibration function, accurate measurement. 6. With online test function, cost-effective. 7. Serial/parallel mode, level and internal resistance are optional. 8. Strong anti-power frequency interference, and the interference level prompts. 9. Automatic gear shift, no manual pre-preparation is required. 10. Test level can be set arbitrarily. Specifications: – Product model: NJ100S (fixed frequency) – Power frequency: 50Hz. Frequency points: 15. Frequency point value: 50, 100, 600, 1000, 6000, 10000, 20000, 30000, 40000, 50000, 60000, 75000, 80000, 93750, 100000. – Power frequency: 60Hz. Frequency points: 13. Frequency point value: 60, 120, 600, 1200, 6000, 12000, 24000, 30000, 38400, 48000, 60000, 75000, 96000. – Measuring ranges: * Resistance: 0.2mΩ~500MΩ * Capacitance: 5fF~150mF * Inductance: 0.5nH~100kH – Product model: NJ101S- Working frequency: 50Hz~100KHz- Stepping: 50Hz~1KHz- Measuring ranges:* Resistance: 0.1mΩ~2000MΩ* Capacitance: 0.003pF~200mF* Inductance: 0.5nH~300kH – Product model: NJ200S- Working frequency: 50Hz~200KHz- Stepping: 10Hz~5KHz- Measuring ranges:* Resistance: 0.1mΩ~2000MΩ* Capacitance: 0.003pF~200mF* Inductance: 0.5nH~300kH – Product model: NJ300S- Working frequency: 50Hz~300KHz- Stepping: 10Hz~10KHz- Measuring ranges:* Resistance: 0.1mΩ~2000MΩ* Capacitance: 0.003pF~200mF* Inductance: 0.5nH~300kH – Display: 2.4″ TFT, resolution 320×240 (QVGA) – Battery capacity: 2000mAH (7.4Wh) – Power consumption: <1W – Charging current: 400mA – Charging port: USB (only as a charging port) – Automatic shutdown: always on, immediately off, 5 minutes ~ 60 minutes (optional) – Measurement parameters: Rs/Xs/Rp/Xp/Cs/Cp/Ls/Lp; |Z|/D/Q/θ/Vrms/Irms – DC bias: None – Display resolution: 6 digits effective value – Measuring speed: online (NJ100S does not have this function), fast, medium, slow – Measurement accuracy: <0.5‰ (within impedance 100mΩ~200MΩ) – Accuracy: <1‰ – Display range: * |Z|, R, X: 0.00001mΩ~9999999MΩ * C: 0.00001pF~9999999F * L: 0.00001nH~9999999H * D, Q: 0.001~99999 * θ (Degrees): -179.9 to 179.9 * Vrms: 0.0001mV~999999mV * Irms: 0.0001nA~999999mA – Level (mVrms): arbitrarily set (1~1000, step 1) -Output impedance: 30Ω, 100Ω (optional) – Model: automatic, series, parallel (optional) – DUT: Automatic, resistance, inductance, capacitance, electrolysis (optional) – Calibration function: open circuit, short circuit (with factory value), load calibration – Appearance size: 130*108*31(mm) – Net weight: 315g – Working temperature: 5℃~40℃ – Atmospheric pressure: 860hPa~1060hPa Functions Overview: – This product has three basic interfaces: measurement, calibration, and system interfaces. The "Measurement" and "Calibration" interfaces also have sub-interfaces. By default, it will enter the main measurement interface when it turns on. – It can easily measure the impedance of about 1mΩ. For example, a wire of 1cm generally has about 6mΩ. – The impedance of 300MΩ can be easily measured, and the actual measurement is 20GΩ. See the pictures below for details. The LCR bridges on the market basically cannot measure such a large impedance. Package Included: – 1 x Set of LCR Meter Note: – Components and other items pictured are not included, for demonstration purposes only. Thank you for your understanding! Precautions: 1. In order to ensure the accuracy of measurement and calibration, please warm up the product for at least 5 minutes before measuring. Especially when doing calibration, it is best to warm up for more than 20 minutes. After warming up, calibration parameters can be more accurate. 2. When powered by a battery, the internal noise of the product is the smallest, so it is recommended to measure under battery power. Especially when doing the calibration operation, it is strongly recommended to do it under battery power supply. When a charger is connected, if the quality of your charger is not good, a certain amount of noise will be generated. 3. Do not connect to a computer's USB charging port for charging. The signal from the USB port will seriously interfere with the working state of the product and cause serious inaccuracy in product measurement. 4. Please try to use better quality fixtures. 5. Before measurement and calibration, please make sure that there is no strong interference signal around, so as not to cause inaccurate measurement results due to interference. 6. When the battery is low, please charge it in time to avoid long-term lack of power. 7. The interface is BNC. Since copper has relatively lower strength than other metals, please try to protect it carefully to avoid falling and bumping damage. 8. In the case of strong interference, unconventional operation, and abnormal software unknown bugs, a crash may occur (the power may be consumed after the crash, until the battery is exhausted). At this time, please directly press the "RESET" hole to reset the product to avoid damage to the battery. If the battery is exhausted and the battery is extremely short of power, the current will be large during charging, and the charger with a small power supply current will have short-circuit protection, but please continue to charge until the battery can be charged normally. 9. When the power is lower than 15%, it will not be able to turn on; when the power is very low, the system will automatically shut down. Please charge in time. 10. When measuring large capacitances (uF level), the "electrolysis" item is more accurate than the "capacitance" item. 11. The device under test cannot be charged, especially the energy storage device (such as electrolytic capacitor), it must be discharged before testing, otherwise it may It will damage the instrument. 12. When measuring milliohm-level devices, if more accurate is required, please perform short-circuit calibration again under the same conditions as the frequency to be measured. 13. When calibrating, try to stay away from the surrounding environment interference, preferably away from the mains, such as wires and sockets. When measuring, use the battery of the instrument to work, do not plug in the USB port for power supply. Payment Terms 1.We accept PayPal only. 2.All major credit cards are accepted through secure payment processor PayPal. 3.Payment must be received within 7 business days of auction closing. 4.We ship to your eBay or Paypal address. Please make sure your eBay and Paypal address is correct before you pay.Shipping Terms – For remote regions, we will charge your extra shipping costs. Usually it cost about 35USD-50USD. We will contact you after your payment. Thanks for your understanding.Return Terms 1. If you receive defective item, please kindly notify us within 14 days. We will guide you the returning instruction for replacement or refund. 2. If you purchased in improper condition, please NOTE that the sipping and handling fee will not be refund, all return shipping fee should paid by the buyer unless item DOA. 3. We reserve the right to refuse any returns for objective reasons.Custom Duties & Taxes 1. Import duties, taxes, and charges are not included in the item price or postage cost. These charges are the buyer's responsibility. 2. Avoiding some unnecessary trouble, please check with your country's customs office to inform us what we should declare its value before shipping.Feedback 1. If you are dissatisfied for any reason, please don't be quick to leave us neutral or negative feedback. We work hard to make sure EVERY CUSTOMER 100% SATISFIED and resolve any problem for you and always leave positive feedback to all our customers. 2. If you are satisfied with the product you received, please kindly leave us a positive feedback and 5 star DSR. If there is any problem of your order, please feel free to contact us firstly, we are responsible and credible seller, will follow it for you asap. On Oct-28-20 at 01:16:34 PDT, seller added the following information:

DER EE DE-5000 High Accuracy Handheld LCR Meter Set Tools with English Manual

Description ◆Features★Automatically selects each LCR parameter and measures at the optimal range★Switches between parallel (Lp, Cp, Rp) and serial (Ls, Cs, Rs) modes★4-wire Kelvin connection measurement/2-wire connection measurement★Test frequency: 100/120/1k/10k/100kHz (0.5Vrms, sine wave)★D: loss factor, Q: quality factor, Θ: phase angle, ESR: equivalent series resistance can be measured!!There is no LCR meter in this price range that can measure this!!★Dual display: main 20000/sub 2000 counts★Relative mode/part classification function★Comes with a Japanese instruction manual provided by the manufacturer!!・Product configuration: DE-5000 (main unit), Japanese and English instruction manual※Includes 1 x 006P battery (9V).ShippingNormal shipping (FedEX,Japan Post) will arrive in 7-14 days. Please note that irregular delays may occur due to weather or customs issues.Expedited】FedEx or EMS : with tracking number Foreign Buyers – Please Note:- Import duties, taxes, and fees are not included in the product price or shipping charges. These costs are the responsibility of the purchaser.- Import duties are not included in the item price or shipping charges.- These charges are usually collected by the delivering freight (shipping) company or upon receipt of the goods.Please do not confuse them with additional shipping charges. .We will be happy to discuss combine shipping and bulk purchases with you prior to payment.Please feel free to contact us at !!!!! Please feel free to contact us at . <Order Processing and Processing TimeYour order will be shipped within 5-10 business days (excluding weekends and holidays) after payment is confirmed. <Compensation/InsuranceIf you are using EMS, in order to receive compensation, you must open the box upon arrival and have the delivery person check the item.In order to receive compensation, you need to open the box upon delivery and have the delivery person check the item. If you fail to do so, you will not be able to receive compensation even if the product is damaged and you will not be able to receive a new product. .In some countries (Germany, France, Italy, Mongolia, Sri Lanka, Turkey, Nigeria, etc.), lithium-ion batteries cannot be handled by EMS or SAL delivery.Please check the regulations of your country. If you are a customer living in one of these countries and place an order, you will be asked to choose one of the following three options1. ship without removing the lithium-ion battery from the product. 2.2. change the shipping method to Fedex or DHL and charge an additional shipping fee; or 3.3. cancel the order. Thank you for your understanding.

Contact us